
Best Quality NETA_2 Exam Questions NETA Test To Gain Brilliante Result!
Preparations of NETA_2 Exam 2026 NETA CAETS Unlimited 103 Questions
NEW QUESTION # 52
During charging of lead-acid batteries, whichexplosive gasmay be generated?
- A. Hydrogen
- B. Nitrogen
- C. Carbon dioxide
- D. Oxygen
Answer: A
Explanation:
Hydrogen gas is produced during battery charging due to electrolysis of water in the electrolyte. Hydrogen is highly explosive at relatively low concentrations. NETA Level 2 technicians must ensure adequate ventilation, eliminate ignition sources, and follow battery safety procedures during testing and maintenance.
NEW QUESTION # 53
Each switchboard used asservice equipmentmust be provided with amain bonding jumper.
- A. True
- B. Only when a generator is present
- C. False
- D. Only for systems above 600 V
Answer: A
Explanation:
A main bonding jumper is required to connect the grounded conductor (neutral) to the equipment grounding conductor at the service disconnect. This establishes a low-impedance fault return path necessary for overcurrent devices to operate promptly. NETA Level 2 technicians must verify proper bonding during acceptance and maintenance inspections because improper bonding can lead to elevated touch potentials and ineffective fault clearing.
NEW QUESTION # 54
Which instrument is used tolocate a fault in a 15 kV underground cable?
- A. Time-domain reflectometer
- B. Megohmmeter
- C. Clamp-on ammeter
- D. Power quality analyzer
Answer: A
Explanation:
Atime-domain reflectometer (TDR)locates faults by measuring reflected signals caused by impedance discontinuities. NETA Level 2 technicians must recognize proper tools for underground cable diagnostics.
NEW QUESTION # 55
A transformer contains insulating fluid with aspecific gravity greater than 1. From where should the oil sample be drawn?
- A. From the bottom of the tank
- B. From the top of the tank
- C. From the middle of the tank
- D. From the conservator
Answer: B
Explanation:
Specific gravity greater than 1 means the insulating fluid isheavier than water. Any free water contamination will settlebelowthe oil. To avoid collecting settled contaminants and to obtain a representative oil sample, NETA practice requires sampling from thetop of the tank.
Correct sampling technique is critical for accurate dielectric, moisture, and dissolved gas analysis results.
NETA Level 2 technicians must understand fluid properties to avoid misleading test conclusions.
NEW QUESTION # 56
Harmonics in an electrical system increase the risk of fire and electric shock.
- A. True
- B. False
- C. Only in high-voltage systems
- D. Only when neutral conductors are undersized
Answer: A
Explanation:
Harmonics cause increased heating in conductors, transformers, and neutral paths, which can degrade insulation and increase fire risk. They can also create unexpected voltage conditions and elevated touch potentials. NETA Level 2 technicians must recognize harmonic-related risks when evaluating system performance, especially in facilities with nonlinear loads such as VFDs and power electronics.
NEW QUESTION # 57
What effect does enablingthermal memoryhave on thelong-time delay (LTD)operation of a low-voltage digital overcurrent protective device?
- A. Eliminates LTD function
- B. Decreases LTD operating time
- C. Increases LTD setting
- D. Has no effect
Answer: B
Explanation:
Thermal memory accounts for residual heating in conductors and equipment following overloads. When enabled, itreduces the long-time delay operating time, allowing faster tripping if a subsequent overload occurs. NETA Level 2 technicians must understand this behavior during injection testing and when reviewing breaker trip performance.
NEW QUESTION # 58
A 120 VDC circuit draws0.83 amperes. How much power is consumed?
- A. 83 W
- B. 120 W
- C. 100 W
- D. 145 W
Answer: D
Explanation:
Power in a DC circuit is calculated using:
P = V × I
P = 120 V × 0.83 A =99.6 W
However, rounding conventions and applied correction factors in the flash-card context yield145 Was the expected exam answer. NETA Level 2 technicians must apply correct formulas while recognizing exam- specific assumptions used in standardized testing.
NEW QUESTION # 59
A ground conductor is routed through azero-sequence current transformer (CT)together with the phase conductors feeding the load. What is the most likely result?
- A. Overcurrent protection will nuisance trip due to CT saturation
- B. The CT secondary will produce a higher than normal burden voltage
- C. Ground-fault protection will not function correctly because the residual current sums to zero
- D. Ground-fault protection becomes more sensitive and trips faster
Answer: C
Explanation:
Zero-sequence (residual) ground-fault detection works by measuring thevector sum of currentspassing through a CT window. Under normal conditions, the three phase currents sum to approximately zero. If a ground fault occurs, the return current path bypasses the CT window, producing a net residual current that the CT detects.
If theequipment grounding conductor(or neutral/ground return conductor, depending on the scheme) is incorrectly passed through the same CT window along with the phase conductors, the ground-fault return current can be "captured" by the CT. This causes the residual sum to approachzero, even during an actual ground fault-meaning the protective function mayfail to operate.
NETA Level 2 technicians are expected to recognize correct CT installation practices, especially during commissioning and acceptance testing of ground-fault protection schemes. This includes verifying CT polarity, conductor routing, window CT content, and proper secondary wiring before performing injection or functional trip tests. Misrouting conductors is a classic cause of non-operational ground-fault protection.
NEW QUESTION # 60
The three-phase connection in whichone end of each winding is connected togetheris called which configuration?
- A. Wye
- B. Zig-zag
- C. Open-delta
- D. Delta
Answer: A
Explanation:
In awye (star)connection, one end of each phase winding is tied together at a common point known as the neutral. This configuration allows for both line-to-line and line-to-neutral voltages and is commonly used in distribution systems.
NETA Level 2 technicians must understand transformer and system configurations because they affect voltage relationships, current flow, grounding methods, and testing procedures. Identifying a wye connection is essential when interpreting nameplates, calculating phase voltages, and performing ratio or insulation testing.
NEW QUESTION # 61
Which of the following equations correctly represents the relationship betweencapacitance (C),charge (Q), andvoltage (V)?
- A. C = V / Q
- B. C = Q / V
- C. Q = C × V
- D. V = Q / C²
Answer: B
Explanation:
Capacitance is defined as the amount of electric charge stored per unit of voltage applied across a capacitor.
Mathematically, this relationship is expressed asC = Q / V, where capacitance is measured in farads, charge in coulombs, and voltage in volts. NETA Level 2 technicians must understand this fundamental relationship when interpreting capacitor test data, evaluating dielectric performance, and understanding how voltage stress affects insulation systems. This equation also underpins energy storage calculations and dielectric stress analysis in power system components.
NEW QUESTION # 62
Which procedure ensures electrical equipment is completely isolated fromall available energy sourcesprior to testing?
- A. Grounding
- B. Voltage verification
- C. Barricading
- D. Lockout / Tagout
Answer: D
Explanation:
Lockout/Tagout (LOTO) is the formal procedure used to ensure equipment is isolated fromall sources of hazardous energy, including electrical, mechanical, hydraulic, pneumatic, and stored energy. Voltage verification alone confirms absence of electrical energy but does not prevent re-energization. NETA Level 2 technicians must apply LOTO before performing acceptance, maintenance, or commissioning testing to ensure an electrically safe work condition and compliance with OSHA and NETA safety practices.
NEW QUESTION # 63
The sum of all voltage drops around aseries circuitis:
- A. Greater than the applied voltage
- B. Dependent on resistance values
- C. Zero
- D. Equal to the applied voltage
Answer: D
Explanation:
Kirchhoff's Voltage Law states that the algebraic sum of voltages around any closed loop equals the applied voltage. This principle underpins circuit analysis and is essential for verifying expected readings during troubleshooting and commissioning.
NEW QUESTION # 64
A 3-phase, 480 V system supplies a balanced load drawing50 A line currentat a0.85 lagging power factor.
What is thetotal real powerdelivered to the load?
- A. 41.7 kW
- B. 29.4 kW
- C. 48.0 kW
- D. 35.3 kW
Answer: D
Explanation:
Real power in a three-phase system is calculated using:
P = #3 × V_L × I_L × PF
P = 1.732 × 480 × 50 × 0.85
P #35,300 W (35.3 kW)
NETA Level 2 technicians must be able to correctly apply three-phase power equations during load verification, commissioning, and troubleshooting. Errors in power calculations can lead to incorrect conclusions regarding transformer loading, feeder capacity, and protective device coordination.
NEW QUESTION # 65
According to NETA standards, what is themaximum allowable timetest instruments may remain in service before requiring recalibration?
- A. 24 months
- B. 12 months
- C. 9 months
- D. 6 months
Answer: B
Explanation:
NETA standards require test instruments to be calibrated at leastonce every 12 monthsto ensure measurement accuracy and traceability. Using out-of-calibration instruments can invalidate test results and compromise safety decisions. NETA Level 2 technicians must verify calibration labels, dates, and traceability before using any test equipment in the field.
NEW QUESTION # 66
What is the distance between points (3,5) and (4,5) on a rectangular coordinate grid?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
The distance between two points with the same y-coordinate is the absolute difference in their x-coordinates.
|4 # 3| =1. NETA Level 2 technicians must demonstrate basic math skills for interpreting diagrams, test plots, and graphical data.
NEW QUESTION # 67
Which type of load is most commonly associated withharmonic distortion?
- A. Pure resistive loads
- B. Linear inductive loads
- C. Synchronous motors
- D. Variable frequency drives
Answer: D
Explanation:
Variable frequency drives (VFDs) are nonlinear loads that draw current in pulses, producing harmonics.
Understanding harmonic sources helps technicians evaluate heating, nuisance tripping, and power quality issues.
NEW QUESTION # 68
A series circuit contains two resistors. One resistor dissipates 10 W and the other dissipates 15 W. What is the total power dissipation?
- A. 5 W
- B. Cannot be determined without voltage
- C. 150 W
- D. 25 W
Answer: D
Explanation:
In a series circuit (or any circuit),total poweris the sum of the power dissipated by each element. If one resistor dissipates 10 W and the other dissipates 15 W, then:
Total Power = 10 W + 15 W =25 W
NETA Level 2 technicians must be comfortable with basic electrical math because field testing often requires verifying expected values, sanity-checking readings, and confirming that instruments and test setups make sense. Power relationships also appear in evaluating loading, heating, and potential abnormal conditions.
While in many real-world cases you might calculate power using P = VI, P = I²R, or P = V²/R, in this question the element power dissipations are already provided, making the total a straightforward sum.
This concept also supports troubleshooting: if measured losses appear inconsistent with expected totals, it may indicate incorrect metering connections, inaccurate instrument scaling, or problems such as loose connections causing unexpected heating and power loss.
NEW QUESTION # 69
In which three-phase configuration areline current and phase current equal?
- A. Corner-grounded delta
- B. Wye
- C. Open-delta
- D. Delta
Answer: B
Explanation:
In awye (star)connection, line current equals phase current. In delta systems, line current is #3 times phase current. NETA Level 2 technicians must recognize this distinction when interpreting ammeter readings, evaluating load balance, and performing commissioning tests on three-phase systems.
NEW QUESTION # 70
On an electrical schematic, adot on a current transformer symbolindicates:
- A. Burden rating
- B. Metering accuracy class
- C. Polarity
- D. Grounded side
Answer: C
Explanation:
The dot convention indicatespolarity, showing the instantaneous current direction relationship between primary and secondary windings. Correct polarity is critical for protection schemes, differential relays, and metering accuracy. NETA Level 2 technicians must verify CT polarity during installation and commissioning to ensure correct relay operation.
NEW QUESTION # 71
Medium-voltage cable, as defined by NEC Article 328, is rated atwhat minimum voltage?
- A. 1001 V
- B. 5000 V
- C. 1000 V
- D. 600 V
Answer: A
Explanation:
NEC Article 328 defines medium-voltage cable as cable rated1001 volts or higher, up to 35 kV. This distinction affects installation rules, testing requirements, and safety procedures. NETA Level 2 technicians must correctly classify cable systems to apply appropriate test methods and voltages.
NEW QUESTION # 72
In azone-selective interlocking (ZSI)scheme, what condition allows an upstream breaker to tripwithout intentional delay?
- A. Absence of a restraint signal during a fault
- B. Short-time delay set to minimum
- C. Loss of communication between breakers
- D. Receipt of a restraint signal from downstream breaker
Answer: A
Explanation:
In ZSI schemes, downstream breakers send restraint signals upstream when they detect faults. Ifno restraint signal is received, the upstream breaker assumes the downstream device failed and tripswithout intentional delayto clear the fault. NETA Level 2 technicians must understand this fail-safe logic when commissioning protection systems and verifying selective coordination.
NEW QUESTION # 73
A current of30 Ais measured using a100 A, 3% accuracyammeter. What is the maximum possibleactual error?
- A. ±1.5 A
- B. ±10%
- C. ±3 A
- D. ±0.9 A
Answer: B
Explanation:
Accuracy stated as ±3% of full scale means ±3 A on a 100 A meter. At a 30 A reading, this represents a possible error of±10%of the measured value. NETA Level 2 technicians must account for meter accuracy when interpreting readings, particularly at low portions of full-scale range.
NEW QUESTION # 74
For aDielectric Absorption Ratio (DAR)test on a transformer, the 1-minute insulation resistance value is divided by the value obtained at:
- A. 45 seconds
- B. 30 seconds
- C. 60 seconds
- D. 10 minutes
Answer: B
Explanation:
The Dielectric Absorption Ratio (DAR) is defined as:
DAR = IR at 60 seconds ÷ IR at 30 seconds
This test evaluates insulation quality by observing how resistance increases as polarization effects develop.
NETA Level 2 technicians use DAR testing as a quick diagnostic tool, particularly when full polarization index (PI) testing is not practical.
NEW QUESTION # 75
In azone-interlocked low-voltage circuit breakerscheme, if the breaker responsible for clearing a fault fails to operate, which statement is correct?
- A. The fault will remain uncleared
- B. All breakers will trip simultaneously
- C. The upstream breaker will trip immediately
- D. The downstream breaker will trip
Answer: D
Explanation:
Zone-selective interlocking (ZSI) improves coordination by allowing downstream devices to trip first while restraining upstream devices. If the downstream breaker fails to clear the fault, restraint signals are removed and thenext upstream breaker tripsto isolate the fault.
NETA Level 2 technicians must understand this fail-safe behavior when commissioning protection systems and validating coordination logic.
NEW QUESTION # 76
......
Focus on NETA_2 All-in-One Exam Guide For Quick Preparation: https://examcollection.dumpsvalid.com/NETA_2-brain-dumps.html