[Oct 25, 2024] Verified D-PSC-MN-01 dumps and 142 unique questions
D-PSC-MN-01 Dumps for Pass Guaranteed - Pass D-PSC-MN-01 Exam 2024
NEW QUESTION # 35
In a Dell PowerScale Gen 6 cluster, which nodes work as a pair?
- A. Nodes in slots 2 and 3
- B. Nodes in slots 1 and 2
- C. Nodes in slots 2 and 4
- D. Nodes in slots 1 and 3
Answer: B
NEW QUESTION # 36
During the replacement of a failed hard drive, a key FRU, what steps should be followed to ensure proper installation?
- A. Verifying the drive firmware version matches the cluster
- B. Ensuring the node is isolated from the network
- C. Confirming the slot and drive compatibility
- D. Performing a full data backup
Answer: A,C
NEW QUESTION # 37
When installing PowerScale Gen 6 nodes, what is an essential hardware capability to verify?
- A. Compatibility with existing rack units
- B. Support for mixed-node clusters
- C. Adequate power supply units
- D. Availability of expansion slots for future upgrades
Answer: C
NEW QUESTION # 38
What phase is crucial in the initial setup of a PowerScale cluster to ensure successful installation and deployment?
- A. Validating hardware and software compatibility
- B. Configuring data protection levels
- C. Assessing network infrastructure
- D. Implementing cluster management tools
Answer: A
NEW QUESTION # 39
What is a critical consideration when handling upgrades and patching in a PowerScale environment?
- A. Scheduling downtime for each node individually
- B. Upgrading the node with the least amount of data first
- C. Testing the upgrades in a staging environment before deployment
- D. Ensuring all nodes are upgraded simultaneously to prevent version mismatch
Answer: C
NEW QUESTION # 40
How do external networking requirements for a PowerScale cluster typically differ from internal requirements?
- A. Simpler routing and switching protocols
- B. Use of public IP addresses
- C. Higher bandwidth and lower latency
- D. Increased security and access controls
Answer: D
NEW QUESTION # 41
What type of NIC is used for the external network on a Dell PowerScale F200 node?
- A. Dual port 10/100 GbE
- B. Single port 10 GbE or dual port 25/40 GbE
- C. Dual port 10/25 GbE or dual port 40/100 GbE
- D. Dual port 10/40 GbE or single port 100GbE
Answer: C
NEW QUESTION # 42
What should be the status of the compute module LED prior to disconnecting any cables or CRUs?
- A. Solid green
- B. Solid white
- C. Solid red
- D. Off
Answer: D
NEW QUESTION # 43
A platform engineer is unable to join a Dell PowerScale node to an existing SmartLock compliance mode cluster.
What is the reason for this issue?
- A. Node was not rebooted into compliance mode before trying to join.
- B. Node is a Gen 6 node, which is not compatible with compliance mode.
- C. Node is an F-series node, which is not compatible with compliance mode.
- D. OneFS version of the existing cluster is 6.
Answer: A
NEW QUESTION # 44
A platform engineer is installing a fully populated Dell PowerScale Gen 6 chassis in a customer rack.
However, the equipment lift is broken.
What is the appropriate course of action to take before attempting to lift the chassis?
- A. Remove and label the drive sleds and compute modules, then rack the chassis with assistance.
- B. Stop work until the lift is repaired and fully functional.
- C. Remove the power supplies and hard drives, then rack the chassis.
- D. Remove the power supplies and drive sleds while waiting for the lift to be repaired.
Answer: A
NEW QUESTION # 45
Which interface can the customer use to automate the retrieval of the most detailed network traffic statistics?
- A. OneFS command line
- B. OneFS API
- C. InsightIQ
- D. Web graphical interface
Answer: B
NEW QUESTION # 46
A federal customer wants to fully restrict the ability to access and modify data on a new Dell PowerScale cluster.
How should the cluster be deployed?
- A. Compliance mode; connected to SRS gateway
- B. Enterprise mode; not connected to SRS gateway
- C. Enterprise mode; connected to SRS gateway
- D. Compliance mode; not connected to SRS gateway
Answer: D
NEW QUESTION # 47
When cabling nodes, what practices should be followed to ensure a successful PowerScale installation? (Select two)
- A. Labeling each cable according to its connection points
- B. Implementing structured cabling that adheres to industry standards
- C. Testing each cable for connectivity and signal integrity
- D. Using cables of standardized lengths to reduce clutter
Answer: A,C
NEW QUESTION # 48
Refer to the exhibit.
A platform engineer has connected power cables to a Dell PowerScale Gen 6 node.
What do the status lights indicate?
- A. Warning event
- B. Cold and redundant
- C. Not functioning
- D. On and healthy
Answer: A
NEW QUESTION # 49
Before replacing any CRUs in a PowerScale node, what is an important safety measure?
- A. Verifying the node's data is fully replicated to other nodes
- B. Ensuring the node is logically removed from the cluster
- C. Documenting the serial numbers of all components
- D. Powering down the node and disconnecting it from the network
Answer: D
NEW QUESTION # 50
When configuring internal networking for a PowerScale cluster, what is a critical requirement?
- A. Implementing redundant switch configurations
- B. Setting up VLAN tagging
- C. Using IPv6 addressing
- D. Ensuring all nodes are in the same subnet
Answer: A
NEW QUESTION # 51
What is a recommended practice when maintaining CRUs in a PowerScale node?
- A. Testing CRUs in a separate environment before installation
- B. Regularly rotating CRUs between nodes to ensure even wear
- C. Using only proprietary tools for CRU installation and removal
- D. Keeping a log of all CRU maintenance activities
Answer: D
NEW QUESTION # 52
Which aspect is crucial when cabling nodes in a PowerScale installation?
- A. Using color-coded cables for easy identification
- B. Documenting the cabling layout
- C. Ensuring cables are of the minimum required length
- D. Verifying cable integrity with testing tools
Answer: B
NEW QUESTION # 53
In the context of PowerScale hardware installation, why is it essential to verify the firmware version of each node?
- A. To ensure compatibility with the cluster's existing nodes
- B. To comply with data security regulations
- C. To facilitate integration with third-party applications
- D. To confirm that all nodes will operate at the same performance level
Answer: A
NEW QUESTION # 54
The Serial Console is used in PowerScale environments primarily for what purpose?
- A. To monitor real-time network traffic
- B. To execute file system commands
- C. For initial setup and configuration
- D. For remote cluster management
Answer: C
NEW QUESTION # 55
How do you ensure data continuity during a PowerScale node hardware upgrade?
- A. Use data mirroring to an external backup cluster
- B. Synchronize all nodes before starting the upgrade
- C. Isolate the node being upgraded from the network
- D. Implement rolling upgrades across the cluster
Answer: D
NEW QUESTION # 56
Which of the following are necessary actions when initializing a new PowerScale cluster? (Select two)
- A. Selecting the appropriate data layout scheme
- B. Configuring the cluster's NTP settings
- C. Implementing role-based access control
- D. Defining network segregation policies
Answer: A,B
NEW QUESTION # 57
......
Latest 100% Passing Guarantee - Brilliant D-PSC-MN-01 Exam Questions PDF: https://examcollection.dumpsvalid.com/D-PSC-MN-01-brain-dumps.html